2005-2013 Corvette Etched Door Sill Plate Guards - Pair. With etched C6 Lettering and Emblem.
Select Brushed or Polished Finish below.
Finally, America Car Craft C6 Corvette GM Licensed Doorsills! It has been a long time coming but our full-length GM Licensed, Etched Doorsills are now available! These doorsills are made from the finest T304 stainless steel and are available in either a Brushed finish (shown) or High Polished finish, that has been hand etched with the Corvette Lettering and Crossed Flags Logo, for the discriminating Corvette owner! These are sold as a set with 3M attachment tape for easy peel and stick installation right over your factory sills. Please select Brushed or Polished, when ordering.
General Motors Trademarks are used under license to American Car Craft.
This is a GM Licensed product.
100% Stainless Steel.
Brushed or High Polished, mirror finish.
Will not tarnish, fade or rust.
Laser cut, for a precise fit.
Adds a unique look and style to your car.
Easy "peel and stick" installation takes just minutes.
Fits all 2005-2013 Coupe and Convertible Corvettes.
Sold as a (2) piece set.
Handcrafted in the USA!
Fits: 2005 2006 2007 2008 2009 2010 2011 2012 2013 Corvettes
Installation Instructions:
PLEASE NOTE THAT THIS IS A PERMANENT INSTALLATION AND THE NEW DOORSILLS CANNOT BE REMOVED WITHOUT DAMAGING THE
PART. PLEASE NOTE YOUR CAR WILL NOT BE DAMAGED IN ANY WAY.
Your new doorsills come to you with a protective liner that you will remove after installation. This will help produce a nice clean install.
1. Thoroughly clean the surface area first with soap and water then with household isopropyl alcohol.
2. Then swipe the same area with the adhesive promoter (provided). This promoter will guarantee a good permanent bond.
3. THIS STEP IS VERY IMPORTANT!!! Gently pre-bend the sills to fit. The metal is flexible enough to allow you to gently curve it so that the sills fit and conform to the door area without forcing it to lay flat. You want the doorsills to look like they are attached (to conform to the shape of the car without any of the doorsill sticking up from the car) to the car before you actually remove the red liner.
4. When you are satisfied with the fit, remove the red liner from the attachment tape and firmly press.
IT IS VERY IMPORTANT THAT YOU SLOWLY INSERT THE SILLS INTO PLACE, KEEPING THE LARGE FLAP AWAY FROM THE CAR.
THE ATTACHMENT TAPE IS VERY RELIABLE AND IT MIGHT BE A GOOD IDEA TO MAKE A COUPLE OF TEST FITS BEFORE PULLING THE RED LINER!
YOU HAVE ONLY ONE SHOT AT THIS SO GO SLOWLY!
5. Once in place pull the protective liner off the sills.
6. OPTIONAL STEP: You have been provided with two lengths of 1/8” chrome molding. This has been supplied should you elect to use the trim to close the small space between the tongue of the sill and the painted surface of the car. To apply swipe a thin bead of the remaining adhesive promoter directly to the paint surrounding the tongue of the stainless sill. Begin by peeling back a small portion of the red release liner as you place the trim onto the paint directly against the new stainless sill, work your way along the edge as you pull the liner pressing the molding firmly to set the trim into position. As you approach the end simply cut the excess molding with a scissor or snap knife and press the end firmly to set.
If you have any questions during installation please call American Car Craft at 727 861-1500. Thank you and enjoy your new purchase.
Note: Care must be taken when cleaning your sills. It is a good idea to lightly dust your sills with a clean soft cloth first in order to prevent any particles from scratching them. Then wipe (using a new clean soft cloth or bounty paper towel) with a good quality streak free glass cleaner.
Return Policy:
If shipping damage occurs, the shipper and EC Products must be notified within 24 hours of delivery.
EC Products stands behind our products 100%. damage during installation is not the responsibility of EC Products and does NOT warrant a free replacement. Feel free to call or e-mail us with any questions, 800-488-5209 or orders@ecproducts.com.
All returns require pre-authorization before refunds, exchanges or credits will be processed.
Returns will be accepted up to 30 days from order date, with approval only. A standard 15% restock fee will be deducted from refund amount.
The customer is responsible for ALL shipping charges incurred in the process of placing the order and returning any part of the order. Returned packages must be sent prepaid, COD packages will be refused and returned at customer's expense. It is recommended that all returns be insured and shipped with a carrier providing a method of tracking in the event the shipment is lost or damaged.
Custom made items are NOT returnable.
